Видео

As ever, thanks Stu! I’m about to begin the diagnosis!

where did you get the float gauge in how do I find one

Launched our Warrior 165 and found that steering locked after laid up for a year. (Ughhhh .... ). Suspected seized cable but saved removal by following the video and noting other possible problems. Issue was seized rod in tube, knocked it out and cleaned up with lots of WD40 and pipe cleaner on a drill. Had to be a bit braver than I would have liked but massive improvement in the end. Thanks, a must see video for diagnosing steering problems.

Nice camera work and explanation. Very helpful.

Great video, will be installing one soon on my new first boat, had no idea about the importance of these filters. Cheers

I hope you are well. Just missing your videos and wanted to say hello.

Miss yins. Hope all is well.

My 93 evinrude 150 starts at home with the water hose hooked up but as soon as i put it in the water it won't start. Any ideas. I'm lost

Can timing cause one side of motor to flood and other half runs? Both have spark... help

You are a genius! You are also a great teacher!

I usually use an angle grinder tapir the edge of the threads spinning as I go

Second time on this Mercury

Great video! Thank you.

starting my adventure understanding my outboard, and hopefully being able to fix it, this was very informative and has helped me understand a lot .

Hey mate in the process now best video iv seen are you just heating with a blow torch

Stu where are you?? We miss your content.

Hi any help on 150 fich lower gear got it out put new prop seals got in bk in but the last hair bit where the little metal clip for the screws I can't get those clips in

Prob don't remember me , I should have never started watching you rebuild that trawler. Ended up buying a boat to restore 3 years later now and getting ready for sea trials once it get the steering finished up . Been missing you stu

If my outboard is in gear will the tilt and trim from the outboard also not work?

Thank you! Really educational needed to see hands on dissambly on how to in case these boat motor trany starts doing something weird.

Thank You I rebuilt my water pump reinstalled my Foot (Lower Unit) No water with muffs.Placed it in a barrel up to the water intake’s and no water. Removed the lower unit 3 more times to re check my work. Scratched my head,slept on it and tried again the next morning NADA! Searching the IT and found your posting. Repositioning the engine in order to get deeper in the barrel and WooHoo, my work is good and proves a point to me that muffs can’t be trusted nor can a barrel if you are not close to the cavation plate. Thanks again and as you said if it were a self priming pump things could have worked but now I know. Stay Safe and Enjoy the Water ✌️

I'm going to need to try this on my older Yamaha 25CV. I'm assuming there's nothing too different between yam and merc. No idea how I'll go, so glad you have this video, thanks!

Love your videos !

I blew my 2007 150 E-Tec. Big End - cylinder 6. The bore lining is badly gouged & the crankshaft where the bearing sits is also damaged. In your opinion can it/is it worth to fix it or just good for parts ?

Please do a video about rebuilding injectors

Hi mate. Very informative video. Can you recommend a good comparison test gauge ?

How do I know which way the drive shaft is supposed to spin, sorry I’m new to this.

Thank you for this video !!

Stu, havent seen any new vids. Hope all is well.

Great video very good explanation on rewind starters .vhe is right them main springs are a nightmare.

Do the evenrudes not have that drive shaft spacer? Displayed at the end with the 2 smaller O rings?

Hi mate, I’m looking at getting one and see this is 4 years old. What’s your opinion of it

I like the idea of using a ratchet strap to help hold the unit in place while you line everything up great idea!!

So what happens if the bendix gear comes out, but still doesn't engage the flywheel? Got a brand new starter, not supposed to have shims, it's for a newer chevy. Bench tested it and everything. It works, bendix comes out it just won't engage the flywheel.

So what's the most common problem with this motor that stops it from running?

You’re the man. I just ordered a new starter. Fried one after an unplugged tether issue. I’m going to rebuild

Better title: prisoner fixes boat

I had to go back and start rewatching some old videos. Stu. You’ve had a break, perfect time to bring back some of these type of videos.

Just dilute it 5:1 in the detergent pot

These videos are great

Love the vid like to see more

Why not use the copper grease on the lower unit bolts?

Any idea how the ball bearing and small shaft on the prop shaft go in. The orientation ie ball first then rounded shaft. On the bf30d

If your going to use the boat as a work shop to go mobile you will miss your chickens if you don't take them with you so you can have someone to talk to lolo

Need help what is the best propeller size for my 40x8ft with cummins 250hp with 2:1 gearbox?

This was extremely helpful in making me understand the timing setup on my Nissan NS70B outboard. You are a great teacher! Thank you.

Very helpful

Thank you for the before and after !! I can’t find another video with the after. I’m sold . Also your video is waaaay more detailed than anything else I could find.

I have always installed pil seaps back to bqck or the lipss facing water & other facing oil. Saw this and questioned it. I can't the answer for a 01 honda bf90 lol.